- AM FM Radios
- WiFi & Internet
- LED Light
- Emergency Supplies
Prices shown in currencies other than US Dollars are estimates based on current exchange rates. We will charge your credit card in US Dollars on the day your order is shipped, and the conversion to your local currency will be done at the prevailing rate by your credit card issuer.
C. Crane will not mark your parcel as a “gift”, declare a value lower than the actual price paid, or otherwise prepare false customs information.
You may have noticed this new acronym popping up on some of our products. RoHS stands for Restrictions on Hazardous Substances, and it's a directive that could have a huge impact on the production and disposal of consumer electronics. First adopted in Europe in 2006 (and later adopted in California in 2007), RoHS restricts the use of six dangerous substances in lots of common electronics. According to the official RoHS compliance Web site (www.rohs.eu), the RoHS symbol indicates that "new electrical and electronic equipment put on the market does not contain any of the six banned substances: lead, mercury, cadmium, hexavalent chromium, poly-brominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE), in quantities exceeding maximum concentration values."
While some military and medical equipment is exempt from RoHS compliance, the electronics governed by the standard are among the most common you'll find in your home, from radios to MP3 players to cell phones and (increasingly) computers. In practical terms, the standard protects factory workers at the production level, sharply reducing their exposure to hazardous substances. The standard also has a profound impact on the disposal and recycling of electronics, in that disposed substances will no longer have at least six of the most hazardous chemicals formerly found in electronics, and recycled electronics will not expose workers to toxics as they harvest components.
The Xtreme-8 Repeater System will repeat distant public WiFi to all the devices in your RV, boat or Big Rig, and there are no drivers to install. The system includes the CC X Mile Omni (which mounts to a pole or ladder outside), a WiFi Hotspot Repeater, and everything you need for an easy set up and great reception. The included 8dBi antenna does not require aiming and receives in all directions. Normal range is 400 ft. and in extreme distances over a mile, with no obstructions.
Compatible with almost all devices that have WiFi.
|Wireless Standard:||IEEE 802.11b
|Frequency Band:||2400~2483 MHz|
|Antenna Gain:||8 dBi|
|Chipset Gain:||22 dBm|
|Data Rate IEEE 802.11b:||11 Mbps|
|Data Rate IEEE 802.11g:||54 Mbps|
|Data Rate IEEE 802.11n:||150 Mbps|
|Receive Sensitivity 11Mbps:||-91dBm @ 802.11b|
|Receive Sensitivity 54Mbps:||-76dBm @ 802.11g|
|Receive Sensitivity 150Mbps:||-74dBm @ 802.11n|
|Power Consumption Voltage:||5V±5%|
|Operation mode:||Infrastructure or Ad hoc|
|Security:||WEP 64/128, WPA, WPA2, WPA-PSK, 802.1x support|
|Wireless Broadcast Range:||Up to 1.5 miles (with 8dbi antenna and no obstructions whatsoever)|
|Certifications:||FCC, ROHS, IP65|
|Antenna Dimensions:||1.5" W x 28" L x 1.5" D. (not including mounting bracket)|
|Operating Temperature:||32° F - 122° F|
|Storage Temperature:||14° F - 149° F|
|Antenna Weight:||1.3 lbs.|
Note: Specifications are subject to change without notice.
MAC OS 10.3
MAC OS 10.4
MAC OS 10.5
MAC OS 10.6
MAC OS 10.7
MAC OS 10.8
Linux Kernel 2.6
|Included Accessories:||30 foot USB Cable
Quick Start Guide
Silicon Grease Pouch
|WiFi Hotspot Repeater Accessory General Specifications|
|Standards||Wired: IEEE 802.3/802.3u
Wireless: 802.11b, 802.11g, 802.11n
|Interface||WAN: 10/100BASE-TX Port * 1
LAN: 10/100BASE-TX Port * 1
USB 2.0 Port * 1
WPA/WPA2-PSK (Pre-Shared Key)
WPA/WPA2 Enterprise mode (802.1x)
WiFi Protected Setup (WPS)
|Advanced Firewall Features||NAT Firewall with SPI
SSID Broadcast Disable
AP Isolation, Client Isolation
|Router Features||Dual WAN (Failover)
Green AP (TX Power Adjustment Scheduling)
|Management Features||Web-base Interface (HTTP)
Remote Management (via WAN)
SNTP Times Synchronize
|USB Wireless Card||AWUS036H|
|Mode||Receiver Sensitivity (dBm)|
|802.11n||20MHz: MCS0 : -90, MCS7 : -71
40MHz: MCS0 : -88, MCS7 : -69
|802.11g||6Mbps : -92
54Mbps : -75
|802.11b||1Mbps : -95
11 Mbps : -90
The USB light will not illuminate until the repeater is successfully connected to another network.
Make sure the WiFi on your device is connected to "Alfa_AP".
You should only need to wait for 1-2 minutes or until the USB light comes on the Hotspot/Repeater. The reason this happens on some wireless devices is due to changing the information from Steps J and K of the Quick Start Guide. You will need to go to your WiFi settings on your device to select the new network that you named from Step J. This can also happen if you have WiFi Assist active where your WiFi device automatically disconnects from networks and connects to other known networks (popular in Windows 10 & iOS7+).
Belkin routers typically have the same IP Address (192.168.2.1) as the WiFi Hotspot Repeater, creating a conflict between the two.
In order to access the Repeater settings in the future, you will need to enter 192.168.8.1 into your browser instead of 192.168.2.1. Make sure to write the new IP address in your instructions.
Some newer versions of Safari are not displaying the correct information of the setup process. Please try a different browser such as Google Chrome or Firefox, or check your Mac, iPhone or iPad device for any software updates. If you already tried Safari first on your device, it may be necessary to restart your device once or twice before proceeding with setup using Google Chrome or Firefox. You can also try using a Windows or Android device to setup the repeater.